Netgear boasts a wide collection of wifi range extenders. Each extender is built for different networking needs. One such masterpiece is EX3700. It is a dual band wifi signal repeater that comes with a direct plug-in design. This particular extender offers wifi speeds of up to 750 Mbps. It effectively cuts off all the wifi dead zones, boosts wifi speed and thus offers dependable connectivity in every single corner of your abode. To leverage all its perks, you must learn about the Netgear EX3700 setup process. So in this particular post we’ll be sharing the important aspects about the same. With no further delay, let’s first unveil the hardware aspects.

Hardware Overview

Firstly the Netgear EX3700 comes with two external antennas, it means wider and stable wifi connectivity is for sure on its way. Now on its front panel, you’ll find four smart indicators. These indicators not only help with accurate placement but also helps you understand about the exact connectivity status. Thereafter, on the side panel it features a reset button, for easy Netgear EX3700 setup it features WPS button and then the power button. Whereas on the other side, you get access to an Ethernet port.

Smart Light Behaviour

Before jumping onto the Netgear EX3700 setup process, it’s quite beneficial to learn about the different light patterns that the device can showcase. So here’s the information regarding the same:

✓ WPS Indicator

When there is no light, it means wifi security isn’t enabled.
Thereafter fluttering green light showcases progress of WPS connection.
Lastly, if the indicator is glowing all green then it means the wifi security is enabled.

✓ Router And Device Link Indicators

When both the above-mentioned indicators are green, it indicates perfect connection and when red, it denotes the opposite which is poor connection.
Whereas, when the indicators are lit up in amber color then it suggests a good connection.

✓ Power Indicator

When the power indicator is fluttering it means the EX3700 device is booting itself up. Thereafter, when it goes solid, it depicts its readiness for the Netgear EX3700 setup process.

Installation Via WPS Key

Now comes the main point which is the setup process. The setup process using WPS key is simple and doesn’t take more than 5 minutes. The accurate steps for it are:

Plug the EX3700 close to the router.
Power it on. If its power indicator doesn’t light up, then push the power button towards ON from the side panel of EX3700.
Now wait for the fluttering power light to turn green.
Thereafter, click the WPS key of EX3700. The WPS indicator must flutter as soon as you click the button.
Moving ahead, click the router’s WPS button.
Now allow the signal repeater to finish the setup process. As the process finishes, the WPS indicators won’t flutter any longer.
If you want to extend the router’s 5G network also then just repeat the above written Netgear EX3700 setup steps once again.
Finally, reposition the device for better networking experience. So plug it halfway from the router and the area of concern. As you repower the device, it will itself sync back with the router.
To know whether the setup is working best to its abilities or not look at the smart indicators. Each one of them must showcase a glowing green light.

Web Browser Based Installation

Require an alternative to the above written Netgear EX3700 setup method? If yes, then this section will lend the helping hand. For this you need access to the browser. The accurate details are written below:

After you hunt out the strategic spot for the EX3700, plug it in a well-working power board.
Power it on. Allow its power indicator to go from fluttering to stable.
Now grab your smart device. Enable its wifi. Pair to the network “Netgear_EXT”. Tap on Connect.
For Netgear EX3700 setup now open a browser. Head to its URL column. In it, type mywifiext.net. Click the Enter key.
Move ahead and tap on the “New Extender Setup” option. Thereafter, fill in all the details and with that click on Next.
Now you’ll be prompted to choose the region. Do the needful and proceed further. Choose the extender mode. Click on Next.
Finally, now the interface starts scanning for the nearby networks. From the list, pick the existing network. Then input the password and click on Next.
Lastly, tie up the setup by personalizing the username and security key of the new network.
You can now choose to register your device or skip it.

Before you log out of the interface, make sure all the smart indicators on EX3700’s front panel are lit up in green color. In case you come across any problem with the installation process, connect to the team of experts without any hesitation.